ASTM C1152 EBOOK DOWNLOAD

This standard is issued under the fixed designation C /C M; the number 1 This test method is under the jurisdiction of ASTM Committee C09 on. ASTM C Standard Test Method for Acid-Soluble Chloride in Mortar and Concrete. Lab ID: Use Specification limits in concrete are intended to minimize. 1 Feb ASTM Ce1 Standard test method for acid-soluble chloride in mortar and concrete. View on Information Provider website {{ linkText }}.

Author: Mek Maulkis
Country: Fiji
Language: English (Spanish)
Genre: Career
Published (Last): 13 April 2008
Pages: 93
PDF File Size: 14.89 Mb
ePub File Size: 14.92 Mb
ISBN: 394-5-98667-888-7
Downloads: 26354
Price: Free* [*Free Regsitration Required]
Uploader: Durn

It is the responsibility of the user of this standard to establish appropriate astm c1152 and health practices and determine the applicability of regulatory limitations prior to use. A number in parentheses indicates the year of last reapproval. Conventional astm c1152 balances shall have a maximum sensibility reciprocal of 0. Such samples may be unrepresentative, especially when the nominal maximum coarse aggregate size is 25 m astm c1152 in.

Penetration of deicer salt and seawater can be assessed by profiling chloride concentration at various positions in the sample. Make a blank determination using 75 mL of water in place of sample.

Results Produced Chloride Cl – astm c1152 determined and reported as weight percentage of the sample.

ASTM Volume Astm c1152 for this method of sampling are as follows: Submit the concrete mix design if the results will be expressed as Cl – percentage of cement.

Print and complete the following order form.

ASTM C1152.C1152M – 04 – Acid-Soluble Chloride in Mortar and Concrete

Time for Results Please contact a Astm c1152 chemical services representative or Project Manager to discuss your individual project needs and testing response times. Ten seconds of boiling is sufficient. Astm c1152 with hydrogen peroxide, as discussed in Asym Methods Cis used to eliminate such interference.

  SRIMAD BHAGAVATAM SLOKAS IN SANSKRIT PDF

Order Form 2 Email complete form astm c1152 contact listed below. In most cases, acid-soluble chloride is equivalent to total chloride.

Record the approximate millivoltmeter reading. Some values have only SI units because the inch-pound equivalents are not used in practice. Other grades may be used, provided it is first ascertained that the reagent is of sufficiently high purity to permit its use without lessening the accuracy of the determination.

Such chloride will be detected by the use of this method. Such chloride will be detected by the use of this method. astm c1152

astm c1152 Instructions Sample mass should be at least 25 grams 1 oz of dried, finely powdered sample. It is the responsibility of the user asgm this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Treatment with hydrogen peroxide, as discussed in Test Methods C, is used to eliminate such interference.

A superscript epsilon indicates an editorial change since the last astm c1152 or reapproval.

ASTM C / CM – 97 Standard Test Method for Acid-Soluble Chloride in Mortar and Concrete

NOTE 5—Slags and slag cements contain sulfide astm c1152 in astm c1152 that can interfere with chloride determination unless oxidized with hydrogen peroxide. NOTE 9—If c11152 tip of the buret is out of the solution, any adhering droplet should be rinsed into the beaker with a few millilitres of water following each titration increment.

Privacy Policy Sensors Sitemap. NOTE 7—It is not necessary to clean all the slurry residue from the sides of the beaker, nor is it necessary that the filter remove all the fine material.

  KLH R5100 MANUAL EBOOK

Account Suspended

For testing to meet water soluble specification limits, tests should be performed on samples at least 28 days old. Specification D for Type I reagent water. Immerse the electrodes into the solution, taking care that astm c1152 stir bar does not strike the electrodes. Some values have only SI units because the inch-pound equivalents are not used in practice. This solution is astm c1152 standard and requires no further standardization.

A digital readout is preferred but not required. Historical Version s – view previous versions of standard. Current edition astm c1152 Dec.

Clean all sampling tools prior to astm c1152 sampling operation See Note 4. Place the delivery tip astm c1152 the 10 mL buret filled to the zero mark with standardized 0. Originally approved in Link to Active This link will always route to the current Active version of the standard. Adtm astm c1152 John S. The alternative designation in parentheses is for information only and does not represent a different standard sieve size. Ast, not allow sample to boil more than a few seconds See Note 6.

The alternative designation in parentheses is for information only and aztm not represent a different standard sieve size. Commercially available standard solutions may be used provided the normality is checked according to the standardization procedure. Heat the covered beaker rapidly to boiling and remove from hot plate. ICS Number Code